Efektifitas Metode V Shape Loading Dengan Cross Loading Terhadap Produktivitas Whell Loader

La Ode Dzakir

Authors

La Ode Dzakir Universitas Sembilanbelas November

Keywords:

Whell Loader, Cross Loading, Cycle Time, Fill Factor, Shape Laoding

Abstract

The research was conducted in regency of Taliabu Island, North maluku province on mining problem studied in this research is to calculate the effectiveness of loading tool production using two methods, namely cross loading and V Shape loading. To solve the problem, firstly do the calculation on the productivity of each of the two methods, such as calculation of cycle time, Fill Factor, Sweel Factor and work efficiency of loading tools. The cycle time from V shape loading method is 30.07 seconds and the cross loading method is 37.40 seconds, the fill Factor for shape loading method is 83% while for the cross loading method is 84%, its Sweel Factor is 80% and the work efficiency from theV Shape Loading method is 79%, while the cross loading method is 76%. Based on results, the effectiveness of the production of V Shape loading method is 308,85 tons/hour while the cross loading method is 248,59 tons/huor.

References

Enos, K. C., Utama, K. C., & Fadhilah, R. (2019). Penerapan Metode V Shape Loading Untuk Meningkatkan Produktivitas PC 2000 & PC 1250 di PIT 10 & 11 Madhani Talatah Nusantara PT. Arutmin Indonesia Tambang Asam. Prosiding TPT XXVIII PERHAPI, 69-79.

Marista, V. N., Lete, M. K., & Yuneta, M. (2023). Analisa Produktivitas Alat Berat Wheel Loader Ditinjau Dari Pekerjaan Di Lapangan Dan Tabel Produktivitas. Journal of Civil Engineering and Infrastructure Technology, 2(1), 61-68.

Muis, A. R. (2007). Penentuan faktor efisiensi kerja operator alat berat wheel loader. Dimensi, 1, 98-101.

Nezhadali, V., Frank, B., & Eriksson, L. (2016). Wheel loader operation—Optimal control compared to real drive experience. Control engineering practice, 48, 1-9.

Norfaeda, R., Akbar, R. M., Saptarini, D. L., & Nurfitriah, N. (2020). Studi Perbandingan Produktivitas Wheel Loader John Deere 744K dan Dump Truck Hino500 FM260TI pada Pemuatan Batubara ke Tongkang di PT. Sembilan Saudara Energi Kalimantan Selatan. Jurnal Poros Teknik, 12(2), 85-90.

Oemiati, N., Revisdah, R., & Rahmawati, R. (2020). Analisa Produktivitas Alat Gali Muat Dan Alat Angkut Pada Pengupasan Lapisan Tanah Penutup (Overburden). Bearing: Jurnal Penelitian dan Kajian Teknik Sipil, 6(3), 194-207.

Prasetyo, R., Margianto, M., & Basjir, M. (2025). Analisis Perawatan Pada Alat Berat Wheel Loader Komatsu Wa380 Di Pt. Sbx Dengan Metode Overall Equipment Effectiveness (Oee) Dan Failure Mode And Effect Analysis (FMEA). Jurnal Teknik Mesin, 22(01), 1-7.

Sidiq, M. M. A. (2022). Analisis Pemilihan Alat Berat Pada Pekerjaan Galian dan Timbunan. Jurnal Teknik Sipil, 15(1), 1-13.

Sulaiman, M. (2017). Analisis Keandalan Alat Berat Terhadap Tingkat Produktivitas Studi Kasus PCS. G-Tech: Jurnal Teknologi Terapan, 1(1), 33-38.

Wang, F., Wen, Q., Xu, X., Xu, B., & Sun, Z. (2021). Site operation strategy for wheel loader/truck loading and transportation cycle. IEEE Transactions on Vehicular Technology, 70(5), 4129-4138.